Retroaktiv SSH – Panel / PCB & Chip

From: £38.00 (Excl. VAT)

Complex Sample & Hold and Waveform Generator with Noise Source

Note: This is a Panel/PCB Set only – for a Full Kit go here

Thonkiconn 3.5mm Audio Jacks with Knurled Nut × 8

B50K - D shaft - Alpha Vertical 9mm Potentiometer × 6

Out of stock

2PS - Medium Pointer (D Shaft) - Rogan PT Plastic Knob × 6

Out of Stock

SKU: Bundle_Retroaktiv_SSH_PanelPCB Categories: , , , , Brand:


The Retroaktiv SSH is a random voltage generator and waveshaper featuring a fully voltage controllable slew. The SSH has a S&H circuit with built in LFO and noise source, allowing for stepped and slewed random waveforms to be generated without any patching or external modules. The stepped S&H waveform can be accessed directly from the STEP output jack, or the waveform can be run through an “intelligent” slew limiter, which allows for smooth slewing between steps. The on-board slew limiter is equipped with a shaping circuit, which allows for the slew to vary between the classic R-C type of glide and linear glide. SSH features some other unique functions, which allow for an amazing variety of waveforms to be generated.

  • On-board LFO with voltage controlled rate, normalised to the sample & hold trigger generator. External triggering input jack as well.
  • Sample & hold generator is normalised to an internal white noise source, allowing for “random” stepped waveforms to be generated. External signals between +/-8V can be sampled using the EXT input jack. Stepped S&H output can be accessed using STEP output jack.
  • Separate output for slewed S&H waveform. (SLEW) Slew amount is voltage controlled. Slope of the slewing is voltage controlled and can be varied between a classic RC glide and linear glide. Using the RISE/BOTH/FALL switch, slew can be active when the S&H waveform is rising, falling, or can be always active (switch in middle position)
  • Symmetry control switch – By using the SYM/ASM switch, slew slope can be “opposite” on rising and falling waveforms. If the SYM mode is selected, the slope of the slewed waveform will correspond to the SLOPE CV controls. If ASM is selected, when the slewed waveform is rising, the current SLOPE setting will be applied. When falling, the “opposite” SLOPE setting will be applied. This allows for RC or linear curves to be applied when the S&H waveform is rising, and the opposite curve to be applied when falling, which allows for unique output waveforms to be created. A rear panel header provides separate 5V RISE and FALL gate signals.
  • The curve of the slewed waveform can also be changed by feeding the slewed output back into the SLEW CV input. Doing this can produce convex rise/ convex fall, concave rise/concave fall types of waveforms.
  • By sampling a gate (0-10V for example), and increasing the rate of sampling, the SSH can be used as an ASR envelope generator with variable slope.

This module is 10HP and packs a sophisticated sample & hold generator, waveshaper, and noise source into a compact module.

Note: This project features mainly SMD components

This bundle includes:

  • SSH 10HP Aluminium Panel
  • SSH bare PCB
  • Programmed MPU Chip

Pots, knobs and jacks are available to add optionally

Power specs: +12v @ 30mA, -12v @ 25mA, 5V @ 10mA

SSH User Manual & Build Guide

SSH Bill Of Materials (BOM)

SSH Schematic (password provided with purchase)


Additional information

HP Size

Thonkiconn 3.5mm Audio Jacks with Knurled Nut

Weight 0.0017 kg

B50K - D shaft - Alpha Vertical 9mm Potentiometer

Weight 0.00493 kg

2PS - Medium Pointer (D Shaft) - Rogan PT Plastic Knob

Weight 0.002 kg

You may also like…